Why is My Dishwasher Leaking?

Coming downstairs only to find an ominous puddle coming from the dishwasher is no-one’s chosen way to start the day.

Thankfully, most commonly seen explanations of dishwasher faults are comparably simple to diagnose and fix on your own. Meaning you may not need to wash the dishes by hand for too long, call an engineer or have to pay the call-out fee.

So, grab the manual if you know where it is, clean up the mess and get a towel clean up any additional leaks and so see whether you can’t fix the problem. If you cannot call us for local dishwasher repair.

Everyday Explanations of Dishwasher Leaks and How to Fix Them

Many of the most everyday sources of dishwasher faults aren’t actually due to a dishwasher issue . Prior to starting getting the tools out and flicking through numerous YouTube tutorials there are a number of problems you should rule out first.

  1. Check to see if your dishwasher is aligned. If the dishwasher is misaligned water will easily pool as well as spill out even if the dishwasher is working perfectly.
  2. Test you are using the proper detergent. You may have seen this with your washer. An excess of soap or using the wrong type may result in to too many bubbles, the suds overflow and you get a spill.
  3. Investigate your dishwasher door closes correctly. If it does not you might have an object blocking it, or you might need to replace the door fixings.
  4. Investigate the filter in the base of the machine for any obvious drainage issues because if your dishwasher isn’t draining properly this will result in fill too much and leak.

If you have looked at these issues it’s time to roll up your sleeves and really begin a thorough check.

To make your life easier start with the door and check for any visible damage in the interior of the machine prior to moving on to the underside. If you can find and mend the problem before you have to pull out the dishwasher you’ll save yourself a lot of hassle.

Also make sure you disconnect the appliance first by either unplugging it or turning off the circuit breaker for the dishwasher.

Door Seal

The door is seemingly the most common place for leakage as well as one of the simplest problems to resolve.

If the leak is occasional the issue may be as simple as a large plate or something else putting pressure against the door thus preventing it from sealing correctly.

On the other hand the door gasket may have been dislodged or been damaged.

Check the door gasket and check for any degradation, mineral deposits or other gunk, or any tracts in which the seal might have separated from the door.

Removing the seal and also giving it a comprehensive scrub has been known to help in some cases or you could have to acquire a new gasket and replace it.

Water Inlet Valve (Solenoid Fill Valve)

The fill valve can also be a common problem. It is generally situated underneath the machine which means you will most likely need to take off the toe board and might have to unscrew the door cover.

The water inlet valve opens and also closes to allow water into the dishwasher at different times in the program. The water inlet valve could be leaking, evidenced by a slow drip, or it may be broken and not operating fully while the dishwasher is running.

If the water inlet valve fails to shut properly this can mean that the dishwasher overfills, causing a leak.

Often these valves are not able to be repaired unless it is just the rubber seal that is faulty, which means the whole valve would need to be changed.

Leaking Hoses

Your dishwasher uses hoses to supply, empty as well as redistribute water within the program.

Two problems can develop when it comes to hoses.

  1. The gaskets can get damaged or the contact points could work loose meaning it’s a good idea to have a look at all the connections .
  2. The other issue than may often happen over time is that hoses can be degraded or cracked.

Luckily broken hoses are simple to procure as well as change.

Pumps and Gaskets

You can visually test the rubber gaskets around the water pumps or motor to determine whether there is a leakage and change them if there is.

The Float Switch

The float itself or the float switch might be faulty resulting in the dishwasher overfilling.

When working as it should the float will lift up as the water level goes up until the desired or maximum water level is attained. The end piece of the float should then turn on the switch. If something is blocking this or the float is broken this could be causing your problem.

Testing the switch will require electrical equipment although it could be obviously damaged in which case replacing it should solve the leak.

Alternative Parts that May Result in a Leak

A damaged wash arm or support can push water under the door resulting in a leak. This could likewise often affect how well your dishes are being cleaned.

Broken or damaged tubes might likewise cause this issue as might a cracked pump cap.

The motor shaft gasket may have cracked causing a leak. This will generally show as a puddle coming from underneath the appliance.

Top Tips to Sort Out Your Machine

  1. Spend less by changing the gasket rather than the whole part. In many cases, you are able to purchase the gasket without the rest of the part which saves time as well as money.
  2. Investigate the simple solutions first. There’s no point pulling the whole machine away from the wall if it’s the soap that’s making the problem.
  3. Take pictures as you go along. This may assist you to put the machine back together, explain the part you are looking for in a shop, and also explain the fault to an engineer if required.
  4. Stay safe. Water and electricity are not good friends so unplug the machine first.
  5. If in doubt call the professionals.

The Next Steps You Should Take If Your Initial Investigation Fails to Identify or Fix the Leakage

If the cause of the problem can’t be discovered the next step you could take is to pull out the machine to get a better look beneath it as well as fill it with water to find out if the leak presents itself.

If this gives no further clues your appliance may only leak when during a cycle. In this instance, you may wish to hire a service engineer to pinpoint as well as fix the leak due to the safety risks of checking for faults with electrical parts exposed.

More Dishwasher Problems:

  • Dishwasher Being Loud
  • Dishwasher Not Turning On
  • Dishwasher Not Draining
  • Dishwasher Not Drying
CLICK-TO-CALL